Adhesive remover

Name: Adhesive remover
Brand: Würth
SKU: 089010063

Adhesive remover
CLNR-STRUCADH-REMOVER-400ML

Art.-no. 089010063

EAN 4053479465319

All versions

Prices for customers after login

Adhesive remover

Art.-no. 089010063

Prices for customers after login

Quantity

Exclusively for trade customers

Login/Register
Call customer service: 023 885171

Solvent mixture for dissolving/removing adhesives and sealants

Good solvent properties

Silicone-free

Notice

Do not use on porous substrates.

Surface/material	Optimisation steps	Notes
Aluminium (AlMg3, AlMgSi1)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary.
Anodised aluminium	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	–
Steel (St 37 etc.)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary. Steel components at risk of corrosion: 2-component PU or epoxy corrosion protection required.
Stainless steel (rustproof)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	–
Zinc-plated steel (hot-dip or zinc-plated)	B and S Activating Cleaner and poss. B and S Adhesion Plus for Metal	Lightly sand with sanding fleece beforehand if necessary.
2-component top-coat paints (PU, epoxy), 2-component water-based primers and paints, cataphoretic paints, primers (EP/2C)	B and S Activating Cleaner	Due to the large number of paints available, this information is only a guide. Where necessary, perform preliminary tests.
Powder coatings	B and S Activating Cleaner	Preliminary testing is recommended for applications involving significant forces or a damp environment.
GFRP (unsaturated polyester), gelcoat side or SMC	B and S Activating Cleaner	Lightly sand with sanding fleece beforehand if necessary.
GFRP (unsaturated polyester), layup side	1. Lightly sand with S 80 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	–
ABS	1. Lightly sand with sanding fleece 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	The sanding process can be omitted for parts subjected to little load.
Hard PVC	1. Lightly sand with sanding fleece 2. B and S Activating Cleaner 3. B and S Primer for P/W/S	The sanding process can be omitted for parts subjected to little load.
Glass (mineral)	B and S Activating Cleaner	Adhesive surface must be protected against UV radiation (opaque cover).
Glass ceramics	B and S Activating Cleaner	–
Untreated wood and wood products (particle board)	1. Dedusting 2. B and S Adhesion Plus for P/W/S	–
Natural stone	1. Dedusting 2. B and S Adhesion Plus for P/W/S	Can cause discolouration when used with sensitive natural stone (marble).
Concrete, mineral mortar and plasters	1. Dedusting 2. B and S Adhesion Plus for P/W/S	–
Textiles, fleeces	B and S Adhesion Plus for P/W/S	Preliminary testing required; the adhesive gripping to the fabric may be sufficient.

The usage instructions are recommendations based on the tests we have conducted and our experience; carry out your own tests before each application. Due to the large number of applications and storage and processing conditions, we do not assume any liability for a specific application result. Insofar as our free customer service provides technical information or acts as an advisory service, no responsibility is assumed by this service except where the advice or information given falls within the scope of our specified, contractually agreed service or the advisor was acting deliberately. We guarantee consistent quality of our products. We reserve the right to make technical changes and further develop products.

Product information

Würth Catalogue

Datasheets(X)

Safety data sheet

Certificates/ Documents

Application area

For removing unhardened PU or hybrid adhesives/sealants from tools and soiled, non-porous surfaces.

Instructions

Remove larger quantities of adhesive/sealant with a spatula. Either spray the remaining contamination with glue remover and wipe off with a clean cloth, or spray remover onto a cloth and wipe down the surfaces.

Contents	400 ml
Chemical basis	Mineral oil
Smell/fragrance	Solvent-like
Colour	Transparent
Density/conditions	0.75 g/cm³ / Active substance, 20°C
Min. flash-off time	0.01 s
Min. flashing point	25 °C
Shelf life from production/conditions	24 Month / at 20°C
AOX-free	Yes
Silicone-free	Yes

Suitable glove:

Product

Description

Nitrile chemical protective glove With cotton velour finish inside

Description:

Permeation level: 6

Nitrile chemical protective glove Long, heavy-duty design

Description:

Permeation level: 6

Permeation is the process by which a chemical moves through the material of a protective glove on a molecular level. The time from the initial contact between the chemical and the glove to the permeation of the material is the breakthrough time.

Measured breakthrough time

Permeation level

< 10 min

≥ 10 min

≥ 30 min

≥ 60 min

≥ 120 min

≥ 240 min

≥ 480 min

Important information:

The information given is based on experience and laboratory conditions and is designed as a guide. However, the actual suitability of a glove depends on the individual conditions of its use and must be confirmed by an appropriate test under operational conditions. Given the variety of materials and chemicals used, the possibility of incompatibility or usage problems for the wearer cannot be excluded in individual cases. We would be happy to advise you about optimum solutions.