SHARK Hammer hammer-in fixing TYPE SK
DWL-(SHARK HAMMER)-SK-PLA-NL-60-8X100
Art.-no. 5906318100
EAN 4061975320902
Register now and access more than 125,000 products
- Quick, cost-effective installation.
- Anchor and nail screw are pre-assembled, no need to search for a suitable screw.
- Suitable for push-through installation.
- Can be removed via drive in screw head.
- Defined integrated hammer-in stop prevents premature expansion.
- Resistant to UV rays.
- Rot-resistant (plastic fixing made of high-quality polyamide).
- Temperature-resistant from -40 °C to +100 °C.
- For countersinking and leaving protruded.
- Countersunk head design countersinks itself in soft wood.
- Halogen free
- European technical assessment ETA-19/0182: SHARK® hammer 6 and 8 for anchors in a redundant non-structural system in concrete.
- European technical assessment ETA-19/0182: SHARK® hammer 8 for anchors in a redundant non-structural system in masonry (exception: dimensions M8 x 45).
| Performance data | ||||
| Anchor diameter [mm] | 6 | 8 | ||
| Permissible tensile load | Concrete B25 or C20/25 | Fperm [kN] | 0,2 | 0,2 |
| Sand-lime brick KS 12 | – | 0,12 | ||
| Hollow sand-lime brick KSL 12 | – | 0,075 | ||
| Characteristic values | ||||
| Tightening torque (THREAD type only) | Tinst [Nm] | 4 | 4 | |
| Drill hole depth | h1 ≥ [mm] | 35 | 45 | |
| Setting depth | hnom ≥ [mm] | 30 | 40 | |
| Thread dia. (THREAD type only) | dthr [mm] | M6 | M8 | |
| Thread length (THREAD type only) | Ithr [mm] | 6 | 9 | |
| Nom. drill dia. | d0 [mm] | 6 | 8 | |
| Hole dia. in comp. | df [mm] | 6,5 | 8,5 | |
Square timbers
Drill the hole
Remove drill cuttings
Anchor sleeve temperature ≥ 0 °C
Temperature in base material ≥ 0 °C
Insert anchor through the component into the drilled hole
Knock in expansion nail until flush
- European technical assessment ETA-19/0182: SHARK® hammer 6 and 8 for anchors in a redundant non-structural system in concrete.
- European technical assessment ETA-19/0182: SHARK® hammer 8 for anchors in a redundant non-structural system in masonry (exception: dimensions M8 x 45).
Datasheets(X)
- Can be used in concrete and masonry.
- For all fastenings in interior finishing, wood, metal, sprinkler, sanitary and electrical areas for light loads, e.g. attachment of square timbers, laths, thin sheets and any components for recessed mounting.
Anchor diameter | 8 mm |
Anchor length (l) | 100 mm |
Max. attachment height (t fix) | 60 mm |
Embedding depth (h nom) | 40 mm |
Nominal drill-bit diameter (d 0) | 8 mm |
Drill hole depth (h 1) | 45 mm |
Hole diameter in component (d f) | 8.5 mm |
Material of nail | Steel |
Surface | Zinc plated |
Internal drive | Z3 |
Last viewed
Pliers for earless clamping jaws for rubber cuffs
Three-star wood jigsaw blade
SCREWDRIVER SLOTTED
Hose pinch-off pliers set for flexible hoses and lines without metal fabric
Storage box
Gear oil ATF 6 low viscosity
Gear oil GL-5 85W-140
WÜRTH MODYF Hercules S3 safety shoe
Spring steel carpenter's square
Non-slip hazard warning adhesive tape, moulds to shapes, laminated with aluminium foil